Fluke Corporation                                           MET/CAL Procedure
=============================================================================
INSTRUMENT:            Fluke 8000A: CAL ADJ /5700
DATE:                  18-Jan-95
AUTHOR:                Fluke Corporation
REVISION:              $Revision: 2.4 $
ADJUSTMENT THRESHOLD:  70%
NUMBER OF TESTS:       1
NUMBER OF LINES:       93
CONFIGURATION:         Philips PM 6666
CONFIGURATION:         Fluke 5700A
=============================================================================
#
# Source:
#   Fluke 8000A instruction manual (PN 347906).
#
# Compatibility:
#   MET/CAL 4.0 or later
#
# Subprocedures:
#   None
#
# Required Files:
#   None
#
# System Specifications:
#   TUR calculation is based on specification interval of the accuracy file.
#   The default 5700A accuracy file contains 90 day specs.
#
# Fluke makes no warranty, expressed or implied, as to the fitness
# or suitability of this procedure in the customer's application.
#
# The 90 day specifications of the 5700A are used in TUR computations.
#
 STEP    FSC    RANGE NOMINAL        TOLERANCE     MOD1        MOD2  3  4 CON
  1.001  ASK-         N                J                                   W
  1.002  HEAD         EQUIPMENT SETUP
  1.003  DISP         Remove the screw located just below the AC line
  1.003  DISP         jack. Slide the instrument out of the case.
  1.004  DISP         Connect the UUT to an ac power source.
  1.004  DISP         Turn the UUT on.
  1.004  DISP         Warm-up time: 1 hour.
  1.004  DISP         Ambient temperature: 22C - 25C.
  1.004  DISP         Relative humidity: less than 70%.
  1.005  HEAD         Period Adjustment
  1.006  DISP         Connect the PM 6666 and UUT as follows:
  1.006  DISP         [32] PM 6666 INPUT A HI to UUT TP5
  1.006  DISP         [32] PM 6666 INPUA A LO to UUT INPUT LO
  1.007  MESS         Adjust R20 for a time period of 100ms (+/-5us).
  1.007  MESS         Variations of the time period must be <= 15us.
  1.008  6666         100mT                        2V             +D PA S  2W
  1.009  MESS
  1.010  DISP         Disconnect the PM 6666 from the UUT.
  1.011  HEAD         ZERO OFFSET ADJUSTMENT
  1.012  DISP         Connect the 5700A and the UUT as follows.
  1.012  DISP         [32] 5700A OUTPUT HI to UUT V-Ohm
  1.012  DISP         [32] 5700A OUTPUT LO to UUT COMMON
  1.012  DISP         [32] 5700A SENSE HI to UUT V-Ohm
  1.012  DISP         [32] 5700A SENSE LO to UUT COMMON
  1.013  RNG          200mV
  1.014  5700         0mV                                               S  2W
  1.015  DISP         Adjust R15 for a UUT display of 00.0+/-00.1.
  1.016  5700         *                                                 S
  1.017  OPBR         Does the UUT read less than or equal to 01.0?
  1.018  JMPF         1.015
  1.019  HEAD         TURN-OVER ERROR ADJUSTMENT
  1.020  5700         190mV                                             S  2W
  1.021  DISP         Adjust R23 for a UUT reading of 190.0mV.
  1.022  5700         -190mV                                            S  2W
  1.023  DISP         Adjust R15 for a UUT reading of 190.0+/-0.1mV.
  1.024  HEAD         RANGE ADJUSTMENTS (DC Volts)
  1.025  5700         190mV                                             S  2W
  1.026  DISP         Adjust R23 for a UUT reading of 190.0+/-0.3mV.
  1.027  5700         *                                                 S
  1.028  RNG          2V
  1.029  5700         1.9V                                              S  2W
  1.030  DISP         Adjust R25 for a UUT reading of 1.900+/-0.003V.
  1.031  5700         *                                                 S
  1.032  HEAD         RANGE ADJUSTMENTS (Ohms)
  1.033  RNG          20MZ
  1.034  5700         19MZ                                              S  2W
  1.035  DISP         Adjust R55 for a UUT reading of 19.00+/-0.11 MOhm.
  1.036  5700         *                                                 S
  1.037  RNG          20kZ
  1.038  5700         19kZ                                              S  CW
  1.039  DISP         Adjust R12 for a UUT reading of 19.00+/-0.05 kOhm.
  1.040  5700         *                                                 S
  1.041  HEAD         RANGE ADJUSTMENTS (High Freq. AC)
  1.042  RNG          20V                          AC
  1.043  5700         19V                          20kH                 S  2W
  1.044  DISP         Adjust C3 for a UUT reading of 19.00+/-0.21V.
  1.045  END